mandriva 2006+driver scheda di rete uli

1 risposta [Ultimo messaggio]
Ritratto di horeb
horeb
(Newbie)
Offline
Newbie
Iscritto: 18/01/2006
Messaggi: 1

ciao a tutto il forum,

ho una scheda madre modello asrock 939 dual sata2 che monta chipset uli 1695 e una scheda di rete integrata sempre chipset uli.

su questa scheda ho installato mandriva 2006 e scaricato dal sito uli i driver per la scheda di rete. dal file readme copio e incollo la seguente procedura:

------------------------------------------------------------------------------------
ULi M5263 10/100M Ethernet Controller Driver for kernel 2.6.x
------------------------------------------------------------------------------------

Copyright (c) 2004-2005, ULi Electronics Inc.

------------------
CONTENTS
------------------
1. ULi M5263 10/100M Ethernet Controller Core
2. File Signature
3. Installation Guide
4. Revision History
5. Disclaimer

1. ULi M5263 10/100M Ethernet Controller Core
=============================================
You can use command
/sbin/lspci -n
or
cat /proc/pci | grep 5263
to determine whether ULi M5263 Ethernet controller exists in your
system. If yes, simply follow the steps below to install the driver.

This driver is dedicated to support ULi M5263 10/100M Ethernet
Controller under Linux platform.

Any improper use of this module, such as combining it with different
hardware and/or software environment, may produce unpredicable results.
The author of the driver and its property owner do not have
responsibility for any property lose or damage.

2. File Signature
====================
/driver/uli526x.c source codec c file
readme.txt this file
====================
/sample/Kconfig.in configuration sample file
/sample/Makefile.in sample makefile

3.Installation Guide
====================
To install the driver, you should reconfigure and recompile your Linux
kernel as follows:

Make sure your kernel version number is 2.6.x.

Copy uli526x.c to /usr/src/linux-2.6.x/drivers/net/tulip/, and modify the
following file in this directory. (Make a backup of them.)

1.Kconfig.in
add the following lines to Kconfig.in file.(refer to the Kconfig.in file we provide to you)

config ULI526X
tristate "ULi M526x controller support"
depends on NET_TULIP && PCI
select CRC32
---help---
This driver is for ULi M5261/M5263 10/100M Ethernet Controller
(<http://www.uli.com.tw/>).

To compile this driver as a module, choose M here.

2.Makefile
add the following lines to Makefile.(refer to the Makefile we provide to you)

obj-$(CONFIG_ULI526X) += uli526x.o
------------------------------------
Install as a kernel module
------------------------------------

Step 1:
Change directory to /usr/src/linux-2.6.x
Use the command "make menuconfig" or "make xconfig", and make
sure "ULi M526x controller support" is set as module.

Example:
Select "Device Drivers"
Select "Networking support"
Select "Ethernet (10 or 100Mbit)"
Select "Tulip family network device support"
Unselect "DECchip Tulip (dc2114x) PCI support"
Select "ULi M526x controller support" as "m"

Step 2:
Select "Loadable module support", and unselect "Set version information
on all module symbols"

Before exit, save your configration.

Step 3:
make modules
make modules_install

Step 4:
rmmod tulip
modprobe uli526x

Then, you can bind any protocol into M5263 driver and use it.

------------------------------------------
Install as a part of linux kernel
------------------------------------------

Step 1:
Change directory to /usr/src/linux-2.6.x
Use the command "make menuconfig" or "make xconfig", and make
sure "ULi M526x controller support" is set as kernel.

Example:
Select "Device Drivers"
Select "Networking support"
Select "Ethernet (10 or 100Mbit)"
Select "Tulip family network device support"
Unselect "DECchip Tulip (dc2114x) PCI support"
Select "ULi M526x controller support" as "y"

Step 2:
Select "Loadable module support", and unselect "Set version information
on all module symbols"

Before exit, save your configration.

Step 3:
make
cp arch/i386/boot/bzImage /boot

Step 4:
If you use grub to boot your linux, then
1) Modify the file /etc/grub.conf by adding
title 2.6.x
root (hd0,2)
kernel /boot/bzImage ro root=/dev/hd1
The disk partition where your linux resides in,
for example: /dev/hda1
2) Reboot and select the kernel 2.6.x

Then, you can bind any protocol into M5263 driver and use it.

4. Revision History
===================
V0.90 - First release.
V0.91 - Change the all ali string to uli string and add the support to ethtool
V0.92 - Change the timeout length for UDP test
V0.93 - Change the tx queue count for UDP test,add non-srom solution

5. Disclaimer
=============
Product names used in this file are for identification purposes only
and may be trademarks of their respective owners.

No part of this file may be copied or reproduced without written
consent from ULi Electronics.

ULi Electronics makes no warranty for the use of its products and
assumes no responsibility for any errors which may appear in this file
nor does it make a commitment to update the information contained
herein.

ULi Electronics retains the right to make changes to these
specifications at any time, without notice.

ma vista la mia niubbagine in linux non so esattamente cosa fare. ho copiato nella cartella tulip il driver ma poi non ho ben capito cosa fare. mi potete aiutare?
ciao e grazie.

horeb

Ritratto di lillox
lillox
(Guru)
Offline
Guru
Iscritto: 29/10/2004
Messaggi: 803

come ti dice il readme devi mettere mano al kernel
quindi scaricati il kernel-source della versione che usi
poi lo compili come modulo e e ,poi. lo fai vedere a grub o lilo-meglio usare grub- certo che se non lo hai mai fatto non è semplicissimo, però è un punto di partenza per la conoscenza di linux.

linux user 384443

http://counter.li.org/